Add to Cart:
Max: 50
Please Choose:SMARC-T4378-800SMARC-T4378-01GSMARC-T4378-800-ISMARC-T4378-01G-ISMARC-T4378-800-I-CSMARC-T4378-01G-I-CEmbedian continues to optimize and expand its portfolio of SMARC solutions for the embedded market. With the Sitara AM4378 processors support for the ARM Cortex-A9 core, extending performance by up to 40 percent over the Sitara AM335X processor line and up to 1GHz. These high performance successors to the popular SMARC-T335X platform integrate additional features to support a variety of markets from human machine interfaces (HMI) to IoT gateways to industrial automation.
In addition to the new Cortex-A9 core, highlights of the SMARC-T4378 include 24-bit parallel LCD interface, dual-port gigabit Ethernet and richer legacy peripherals.
SMARC-T4378 supports both SMARC 1.0 and SMARC 1.1 standards (automatically detect). Technical Information
Part Number
Example: SMARC-T4378-800: SMARC-T4378 module with Sitara AM4378 processor running at 800Mhz and uses 512MB DDR3L in normal temperature
Compliance
SMARC 1.0 _and_ SMARC 1.1 (same P/N)
Dimension (W x L)
82mm x 50mm
CPU
Sitara AM4378
1 ARM Cortex-A9
800MHz or 1GHz
Main Memory
512MB DDR3L (with 800MHz Processors)
1GB DDR3L (with 1GHz Processors)
4GB eMMC (5.x) flash onboard
4MB SPI NOR Flash onboard
AT24C32 EEPROM onboard
Graphic Controller
SGX530 2D/3D Acceleration
Display Interfaces
24 bit parallel RGB LCD data and control signals
SDIO Interfaces
Two SDIO interfaces
SPI Interfaces
Two SPI interfaces
I2S Interfaces
One I2S interface
I2C Interfaces
Three I2C interfaces
Asynchronous Serial Port (UART) Interfaces
Four asynchronous serial ports
Two with 4 wire with handshake (RXD, TXD, RTS#, CTS#)
Two with data only (RXD, TXD)
Logic level interface
CAN Bus Interfaces
Two CAN bus interfaces
USB Interfaces
Two USB Ports allow USB 2.0 Host operation (Full Speed and High Speed)
One port allows USB 2.0 OTG (USB client or host)
USB support signals (VBUS enable / Over-current detects, OTG support signals)
Gigabit Ethernet
Two analog GBE MDI interfaces (Qualcomm Atheros AR8035 PHY onboard)
No magnetics on Module
LED support signals
CTREF (center tap reference voltage) for Carrier magnetic
Watchdog Timer Interfaces
Real-Time Clock
External Seiko S35390A onboard
General Purpose I/O
Twelve GPIO signals
Specific alternate functions are assigned to some GPIOs
PWM / Tachometer capability
Camera support
CAN Error Signaling
HD Audio reset
System and Power Management Signals
Reset out and Reset in
Power button in
Power source status
Module power state status
System management pins
Battery and battery charger management pins
Carrier Power On control
Power Consumption (Typical)
Typical: 2.1W
Boot Source Select
Three pins to allow selection from Carrier Board
Select options to include boot from one of the following:
Power Supply
3V to 5.25V:
Operates directly from single level Lithium Ion cells, or fixed 3.3V or 5V power supply
Software
Linux:
Linux Kernel 4.9.41 (Based on TI Processor SDK 04.01.00.06) or
Linux Kernel 4.4.12 (Based on TI Processor SDK 03.00.00.04) or
Linux Kernel 4.1.13 (Based on TI Processor SDK 02.00.01.07)
Yocto Project Support
Ubuntu 14.04/16.04 LTS or Debian 9 Support
Form Factor
SMARC:
82 mm x 50 mm by SMARC Specification
Evaluation Baseboard (EVK-STD-CARRIER)
Features:
12V~24V Power input with 2.5mm DC Jack connector
Audio Jack
RTC backup battery holder
Buzzer
LVDS, VGA DSUB15 (from 24-bit parallel LCD) and HDMI connector
2 x 10/100/1000Mbps RJ-45 connector
1 x 4-wire resistive touch connector
2 x RS232/422/485 DSUB9 connector, 2 x RS232 2.0mm Header
2 x USB host 2.0 type A connector, 1 x mini USB client connector
1 x PCIe connector, 2 x mini PCIe connector
2 x CAN BUS header, 1 x 2x7-pin GPIO header, Audio Mic. in and Speaker out Audio Jack
2 x I2C Connector (for capacitive touch), 4 x SPI connector, 1 Camera/MIPI header
1 x SDHC connector, 1 x onboard eMMC
A single 4KB EEPROM is provided on I2C0 that holds the board information. This information includes board name, serial number, and revision information.
1 x external watchdog reset
jumpers for LCD 3.3V or 5V voltage, boot selection, RS232 or RS485 selection, SMARC 1.0 or SMARC 1.1 selection
Form factor: 170mm (L) x 170mm (W) (mini-ITX form factor)
Customers who bought this product also purchased... |