Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Freescale makes their i.MX series official bsp build scripts available via the following GIT repository:
Info
iconfalse

git://git.freescale.com/imx/meta-fsl-bsp-release

 

Freescale community BSP release build script is available via the following repository: 

 

Info
iconfalse

git://git.freescale.com/imx/fsl-arm-yocto-bsp.git

It is this repository that actually pulls in the fsl-bsp-release project to perform the Linux BSP builds for Freescale's i.MX6 ARM Cortext-A9 chips.  

Generating SSH Keys


 We recommend you use SSH keys to establish a secure connection between your computer and Embedian Gitlab server. The steps below will walk you through generating an SSH key and then adding the public key to our Gitlab account. 

Step 1. Check for SSH keys


First, we need to check for existing ssh keys on your computer. Open up Git Bash and run: 

Code Block
themeConfluence
languagecpp
$ cd ~/.ssh
$ ls
# Lists the files in your .ssh directory

 Check the directory listing to see if you have a file named either id_rsa.pub or id_dsa.pub. If you don't have either of those files go to step 2. Otherwise, you already have an existing keypair, and you can skip to step 3. 

Step 2. Generate a new SSH key


 To generate a new SSH key, enter the code below. We want the default settings so when asked to enter a file in which to save the key, just press enter.

Code Block
themeConfluence
languagecpp
$ ssh-keygen -t rsa -C "your_email@example.com"
# Creates a new ssh key, using the provided email as a label
# Generating public/private rsa key pair.
# Enter file in which to save the key (/c/Users/you/.ssh/id_rsa): [Press enter]
$ ssh-add id_rsa

 Now you need to enter a passphrase.

Code Block
themeConfluence
languagecpp
Enter passphrase (empty for no passphrase): [Type a passphrase]
Enter same passphrase again: [Type passphrase again]

 Which should give you something like this:

Code Block
themeConfluence
languagecpp
Your identification has been saved in /c/Users/you/.ssh/id_rsa.
Your public key has been saved in /c/Users/you/.ssh/id_rsa.pub.
The key fingerprint is:
01:0f:f4:3b:ca:85:d6:17:a1:7d:f0:68:9d:f0:a2:db your_email@example.com

Step 3. Add your SSH key to Embedian Gitlab Server


 Copy the key to your clipboard.

Code Block
themeConfluence
languagecpp
$ cat ~/.ssh/id_rsa.pub
ssh-rsa AAAAB3NzaC1yc2EAAABDAQABAAABAQDQUEnh8uGpfxaZVU6+uE4bsDrs/tEE5/BPW7jMAxak
6qgOh6nUrQGBWS+VxMM2un3KzwvLRJSj8G4TnTK2CSmlBvR+X8ZeXNTyAdaDxULs/StVhH+QRtFEGy4o
iMIzvIlTyORY89jzhIsgZzwr01nqoSeWWASd+59JWtFjVy0nwVNVtbek7NfuIGGAPaijO5Wnshr2uChB
Pk8ScGjQ3z4VqNXP6CWhCXTqIk7EQl7yX2GKd6FgEFrzae+5Jf63Xm8g6abbE3ytCrMT/jYy5OOj2XSg
6jlxSFnKcONAcfMTWkTXeG/OgeGeG5kZdtqryRtOlGmOeuQe1dd3I+Zz3JyT your_email@example.c
om

Go to Embedian Git Server. At Profile Setting --> SSH Keys --> Add SSH Key 

Paste your public key and press "Add Key" and your are done.

Overview of the meta-smarcfimx6-sumo Yocto Layer


The supplied meta-smarcfimx6-sumo Yocto compliant layer has the following organization:

Info
iconfalse

.
|-- conf
|   |-- layer.conf
|   |-- site.conf
|   |-- machine
|       |-- imx6qp1gsmarc.conf
|       |-- imx6qp2gsmarc.conf
|       |-- imx6q1gsmarc.conf
|       |-- imx6q2gsmarc.conf
|       |-- imx6u1gsmarc.conf
|       |-- imx6s1gsmarc.conf
|   |   `-- imx6solosmarc.conf
|-- README
|-- recipes-bsp
|   |-- u-boot
|       `-- u-boot-smarcfimx6_2017.03.bb
|   |-- pm-utils
|       `-- pm-utils_%.bbappend

|-- recipes-core
|   |-- base-files
|       `-- base-files_%.bbappend
|       |   |-- base-files
|       |   |   |-- eth.network
|       |   |   `-- wlan.network
|   |-- psplash
|       `-- psplash_git.bbappend
|       |   |-- files
|       |   |   `-- psplash-poky-img.h
|   |-- udev
|       `-- udev-rules-imx.bbappend
|       |   |-- files
|       |   |   `-- usb-power.rules

|   |-- busybox
|       `-- busybox_%.bbappend
|       |   |-- busybox
|       |   |   |-- ftpget.cfg
|       |   |   `-- defconfig
|   |-- packagegroups
|       `-- packagegroup-core-tools-testapps.bbappend
|-- recipes-multimedia

|   |-- gst-plugins-good
|   |   |-- files
|           `-- increase_min_buffers.patch
|   |-- pulseaudio
|   |   |-- pulseaudio
|       |   |   |-- default.pa
|       |   |   |-- init
|       |   |   |-- pulseaudio-bluetooth.conf
|       |   |   |-- pulseaudio.service
|       |   |   `-- system.pa
|       `-- pulseaudio_%.bbappend
`-- recipes-kernel
|   |-- linux
|       `-- linux-smarcfimx6_4.9.88.bb


Notes on 
meta-smarcfimx6-sumo layer content

conf/machine/*

This folder contains the machine definitions for the imx6qp1gsmarc|imx6qp2gsmarc|imx6q1gsmarc|imx6q2gsmarc|imx6u1gsmarc|imx6solosmarc platform and backup repository in Embedian. These select the associated kernel, kernel config, u-boot, u-boot config, and tar.bz2 image settings.

recipes-bsp/u-boot/*

This folder contains recipes used to build DAS U-boot for imx6qp1gsmarc|imx6qp2gsmarc|imx6q1gsmarc|imx6q2gsmarc|imx6u1gsmarc|imx6solosmarc platform.

recipes-core/busybox/*

This folder remove telnetd from bysybox for imx6qp1gsmarc|imx6qp2gsmarc|imx6q1gsmarc|imx6q2gsmarc|imx6u1gsmarc|imx6solosmarc platform.  

recipes-core/base-files/*

This folder adds network configurations for imx6qp1gsmarc|imx6qp2gsmarc|imx6q1gsmarc|imx6q2gsmarc|imx6u1gsmarc|imx6solosmarc platform.

recipes-core/psplash/*

This folder adds boot splash screen  for imx6qp1gsmarc|imx6qp2gsmarc|imx6q1gsmarc|imx6q2gsmarc|imx6u1gsmarc|imx6solosmarc platform.

recipes-core/udev/* 

This folder adds udev rules  for imx6qp1gsmarc|imx6qp2gsmarc|imx6q1gsmarc|imx6q2gsmarc|imx6u1gsmarc|imx6solosmarc platform.

recipes-kernel/linux/*

Contains the recipes needed to build the imx6qp1gsmarc|imx6qp2gsmarc|imx6q1gsmarc|imx6q2gsmarc|imx6u1gsmarc|imx6solosmarc Linux kernels.

Setting Up the Tools and Build Environment


To build the latest Freescale i.MX6 fsl-bsp-release, you first need an Ubuntu 16.04 LTS installation. Since bitbake does not accept building images using root privileges, please do not login as a root user when performing the instructions in this section. 

Once you have Ubuntu 16.04 LTS running, install the additional required support packages using the following console command:

Info
iconfalse

$ sudo apt-get install gawk wget git-core diffstat unzip texinfo build-essential chrpath libsdl1.2-dev xterm python-m2crypto bc libsdl1.2-dev 

If you are using a 64-bit Linux, then you'd also need to install 32-bit support libraries, needed by the pre-built Linaro toolchain and other binary tools.

Info
iconfalse

$ sudo dpkg --add-architecture i386
$ sudo apt-get update
$ sudo apt-get install curl g++-multilib gcc-multilib lib32z1-dev libcrypto++9:i386 libcrypto++-dev:i386 liblzo2-dev:i386 libusb-1.0-0:i386 libusb-1.0-0-dev:i386 uuid-dev:i386

Note

If you saw error like the following after running "sudo dpkg --add-architecture i386"

pkg: error: unknown option --add-architecture

make sure the only file present in /etc/dpkg/dpkg.cfg.d/ is "multiarch"

ls /etc/dpkg/dpkg.cfg.d/

if output is

multiarch

execute the following commands as it is else replace "multiarch" with the name of file present in that directory.

$ sudo sh -c "echo 'foreign-architecture i386' > /etc/dpkg/dpkg.cfg.d/multiarch"

The above command will add i386 architecture.


To get the BSP you need to have 'repo' installed and use it as:

Install the 'repo' utility:

Info
iconfalse

$ mkdir ~/bin
$ curl http://commondatastorage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo
$ PATH=${PATH}:~/bin 


Download the BSP Yocto Project Environment.
Info
iconfalse
$ mkdir ~/smarc-fimx6-sumo-release
$ cd ~/smarc-fimx6-sumo-release
$ repo init -u https://source.codeaurora.org/external/imx/imx-manifest -b imx-linux-sumo -m imx-4.14.98-2.0.0_ga.xml
$ repo sync

Download the Embedian Yocto build script and meta layer.

 

Info
iconfalse
$ wget ftp://ftp.embedian.com/public/dev/minfs/smarc-fimx6-bsp-release/fsl-smarcfimx6-sumo-setup-release.sh
$ chmod 444 fsl-smarcfimx6-sumo-setup-release.sh
$ cd sources

$ git clone git@git.embedian.com:developer/meta-smarcfimx6-sumo.git
$ cd ~/smarc-fimx6-sumo-release
$ DISTRO=fsl-imx-fb MACHINE=imx6q1gsmarc source fsl-smarcfimx6-sumo-setup-release.sh -b imx6q-build-qt5fb 

This script will create and bring you to 
~/smarc-fimx6-sumo-release/imx6q1g-build-qt5fb directory.

 

Note
titleNote

The last line of the above script

$ DISTRO=<distro name> MACHINE=<machine name> source smarc-sumo-fsl-setup-release.sh -b <build dir>
  1. <distro name> 
    • fsl-imx-x11 - Only X11 graphics
    • fsl-imx-wayland - Wayland weston graphics
    • fsl-imx-xwayland - Wayland graphics and X11. X11 applications using EGL are not supported
    • fsl-imx-fb - Frame Buffer graphics - no X11 or Wayland
  2. <machine name>
    • imx6qp1gsmarc - if your SMARC-FiMX6 is a quad plus core CPU and 1GB DDR3L memory
    • imx6qp2gsmarc - if your SMARC-FiMX6 is a quad plus core CPU and 2GB DDR3L memory
    • imx6q1gsmarc  - if your SMARC-FiMX6 is a quad or dual core CPU and 1GB DDR3L memory
    • imx6q2gsmarc  - if your SMARC-FiMX6 is a quad or dual core CPU and 2GB DDR3L memory
    • imx6u1gsmarc  - if your SMARC-FiMX6 is a dual lite core CPU and 1GB DDR3L memory
    • imx6s1gsmarc - if your SMARC-FiMX6 is a solo core CPU and 1GB DDR3L memory
    • imx6solosmarc - if your SMARC-FiMX6 is a solo core CPU and 512MB DDR3L memory

The default console debug port is SER3.

In this document, we will use imx6q1gsmarc as the example of machine name. Users need to change different machine name if you have different SMARC card variants.

 
Building the target platforms

 To build Embedian/Freescale Yocto BSP, use the following commands:
Info
iconfalse

$ MACHINE=imx6q1gsmarc bitbake -k fsl-image-qt5-validation-imx
or
$ MACHINE=imx6q1gsmarc bitbake -k fsl-image-validation-imx


Note
titleNote

fsl-image-validation-imx provides a gui image without QT5. 

fsl-image-qt5-validation-imx provides a Qt5 image for X11, wayland or FB backends depending on your distro name.

 
If your machine name is imx6q1gsmarc and your gui image is without QT5 , the following command gives you as an example.
 
$ MACHINE=imx6q1gmarc bitbake -k fsl-image-validation-imx
 
The first build takes time. 

 

Once it done, you can find all required images under ~/smarc-fimx6-sumo-release/<build directory>/tmp/deploy/images/<machine name>/

You may want to build programs that aren’t installed into a root file system so you can make them available via a feed site (described below.) To do this you can build the package directly and then build the package named package-index to add the new package to the feed site.

 

The following example builds the minicom program and makes it available on the feed site:

Info
iconfalse
$ MACHINE=imx6q1gsmarc bitbake tcpdump 
$ MACHINE=imx6q1gsmarc bitbake package-index

Once the build(s) are completed you’ll find the resulting images, rpm and licenses in folder ~/smarc-fimx6-sumo-release/<build directory>/tmp/deploy.

deploy/images/<machine name>/* 

This folder contains the binary images for the root file system and the Embedian SMARC-FiMX6 specific version of the u-boot, zImage and device tree file. Specifically the images are:

deploy/images/<machine name>/u-boot.imx 

This u-boot bootloader binary for SMARC-FiMX6

deploy/images/<machine name>/zImage

The kernel zImage for SMARC-FiMX6.  

deploy/images/<machine name>/imx6qp-smarcfimx6.dtb

The device tree binary file for SMARC-FiMX6 QuadPlus core. 

deploy/images/<machine name>/imx6qp-smarcfimx6-<resolution>.dtb 

The device tree binary file for SMARC-FiMX6 QuadPlus core with LVDS output for specific display resolutions.

deploy/images/<machine name>/imx6q-smarcfimx6.dtb

The device tree binary file for SMARC-FiMX6 Quad and Dual core.

deploy/images/<machine name>/imx6q-smarcfimx6-<resolution>.dtb 

The device tree binary file for SMARC-FiMX6 Quad or Dual core with LVDS output for specific display resolutions.

deploy/images/<machine name>/imx6dl-smarcfimx6.dtb 

The device tree binary file for SMARC-FiMX6 Solo or Dual Lite core.  

deploy/images/<machine name>/imx6dl-smarcfimx6-<resolution>.dtb

The device tree binary file for SMARC-FiMX6 Solo or Dual Lite core with LVDS output for specific display resolutions.

deploy/images/<machine name>/fsl-image-validation-imx-<machine name>.*

Embedian root file system images for software development on Embedian’s SMARC-FiMX6  platforms without QT5.

deploy/images/<machine name>/fsl-image-qt5-validation-imx-<machine name>.*

Embedian root file system images for software development on Embedian’s SMARC-FiMX6  with QT5.


deploy/rpm/*

 This folder contains all the packages used to construct the root file system images. They are in rpm format (similar format to Fedora packages) and can be dynamically installed on the target platform via a properly  constructed feed file. Here is an example of the feed file (named imx6q1g_qt5fb_update.repo) that is used internally at Embedian to install upgrades onto a imx6q1gsmarc QT5 platform directly on framebuffer without reflashing the file system:

Info
iconfalse

[noarch]
type = rpm-md
baseurl = http://www.embedian.com/smarcfimx6-yocto-sumo-feed/imx6q1gsmarc/fb/qt5/noarch
[cortexa9hf_neon]
type = rpm-md
baseurl = http://www.embedian.com/smarcfimx6-yocto-sumo-feed/imx6q1gsmarc/fb/qt5/cortexa9hf_neon
[cortexa9hf_neon_mx6qdl]
type = rpm-md
baseurl = http://www.embedian.com/smarcfimx6-yocto-sumo-feed/imx6q1gsmarc/fb/qt5/cortexa9hf_neon_mx6qdl
[imxq1gsmarc]
type = rpm-md
baseurl = http://www.embedian.com/smarcfimx6-yocto-sumo-feed/imx6q1gsmarc/fb/qt5/imx6q1gsmarc


deploy/licenses/* 
A database of all licenses used in all packages built for the system.

Setup SD Card


For these instruction, we are assuming: DISK=/dev/mmcblk0, "lsblk" is very useful for determining the device id.

Info
iconfalse
$ export DISK=/dev/mmcblk0

Erase SD card:

Info
iconfalse

$ sudo dd if=/dev/zero of=${DISK} bs=1M count=16

Create Partitions:

Info
titlesfdisk >=2.26.x
$ sudo sfdisk ${DISK} <<-__EOF__
1M,48M,0x83,*
,,,-
__EOF__
Info
titlesfdisk <=2.25
$ sudo sfdisk --in-order --Linux --unit M ${DISK} <<-__EOF__
1,48,0x83,*
,,,-
__EOF__

Format Partitions:

Info
iconfalse
for: DISK=/dev/mmcblk0
$ sudo mkfs.vfat -F 16 ${DISK}p1 -n boot
$ sudo mkfs.ext4 ${DISK}p2 -L rootfs
 
for: DISK=/dev/sdX
$ sudo mkfs.vfat -F 16 ${DISK}1 -n boot
$ sudo mkfs.ext4 ${DISK}2 -L rootfs

Mount Partitions:

On some systems, these partitions may be auto-mounted...

Info
iconfalse
$ sudo mkdir -p /media/boot/
$ sudo mkdir -p /media/rootfs/
 
for: DISK=/dev/mmcblk0
$ sudo mount ${DISK}p1 /media/boot/
$ sudo mount ${DISK}p2 /media/rootfs/
 
for: DISK=/dev/sdX
$ sudo mount ${DISK}1 /media/boot/
$ sudo mount ${DISK}2 /media/rootfs/

Install Bootloader

If SPI NOR Flash is not empty

The u-boot.imx is pre-installed in SPI NOR flash at factory default. SMARC-FiMX6 is designed to always boot up from SPI NOR flash and to load zImage, device tree blob and root file systems based on the setting of BOOT_SEL. If users need to fuse their own u-boot or perform u-boot upgrade. This section will instruct you how to do that.

 Copy u-boot.imx to the first boot partition of your SD card.

Info
iconfalse
title~/smarc-fimx6-sumo-release/<build dir>/tmp/deploy/images/<machine name>/

$ sudo cp -v u-boot.imx /media/boot/u-boot.imx

Fuse u-boot.imx to the SPI NOR flash.

Stop at U-Boot command prompt (Press any key when booting up). Copy and Paste the following script under u-boot command prompt.

Info
iconfalse
titleu-boot command prompt

U-Boot# mmc rescan; mmc dev; load mmc 0:1 0x10800000 u-boot.imx; sf probe; sleep 2; sf erase 0 0xc0000; sf write 0x10800000 0x400 a0000

If SPI NOR Flash is empty

In some cases, when SPI NOR flash is erased or the u-boot is under development, we need a way to boot from SD card first. Users need to shunt cross the TEST# pin to ground. In this way, SMARC-FiMX6 will always boot up from SD card. 

 Copy u-boot.imx to the SD card

Info
iconfalse
title~/smarc-fimx6-sumo-release/<build dir>/tmp/deploy/images/<machine name>/

$ sudo dd if=u-boot.imx of=${DISK} bs=512 seek=2 
Note
  1. If your u-boot hasn't been finalized and still under development, it is recommended to shunt cross the test pin and boot directly from SD card first. Once your u-boot is fully tested and finalized, you can fuse your u-boot to SPI NOR flash.
  2. When TEST# pin of SMARC-FiMX6 is not shunt crossed, it will always boot up from SPI NOR flash. U-boot will read the BOOT_SEL configuration and determine where it should load zImage and device tree blob. When TEST# is shunt crossed (pull low), it will always boot up from SD card.

uEnv.txt based bootscript

Create "uEnv.txt" boot script: ($ vim uEnv.txt)

Info
iconfalse
title~/uEnv.txt

#####HDMI######
#optargs="video=mxcfb0:dev=hdmi,1280x720M@60,if=RGB24,bpp=32 consoleblank=0"
#####LVDS#####
#optargs="video=mxcfb0:dev=ldb,if=RGB24,bpp=32 consoleblank=0 fbmem=24M vmalloc=400M"
#####Parallel LCD Setting#####
#optargs="video=mxcfb0:dev=lcd,CLAA-WVGA,if=RGB24,bpp=32 consoleblank=0 fbmem=24M vmalloc=400M"
#####Parallel LCD to CH7055A (VESA Timing Format) Setting #####
#optargs="video=mxcfb0:dev=lcd,768x576M@75,if=RGB24,bpp=32 consoleblank=0"
#optargs="video=mxcfb0:dev=lcd,1280x1024M@60,if=RGB24,bpp=32 consoleblank=0"
#optargs="video=mxcfb0:dev=lcd,640x480M@60,if=RGB24,bpp=32 consoleblank=0"
console=ttymxc4,115200
mmcdev=0
mmcpart=1
image=zImage
loadaddr=0x12000000
fdt_addr=0x18000000
mmcroot=/dev/mmcblk1p2 ro
mmcrootfstype=ext4 rootwait fixrtc
netdev=eth0
ethact=FEC0
ipaddr=192.168.1.150
serverip=192.168.1.53
gatewayip=192.168.1.254
mmcargs=setenv bootargs console=${console} root=${mmcroot} rootfstype=${mmcrootfstype} ${optargs}
uenvcmd=run loadzimage; run loadfdt; run mmcboot

Copy uEnv.txt to the boot partition:

Info
iconfalse
title~/

$ sudo cp -v ~/uEnv.txt /media/boot/

Install Kernel zImage

Copy zImage to the boot partition:

Info
iconfalse
title~/smarc-fimx6-sumo-release/<build dir>/tmp/deploy/images/<machine name>/

$ sudo cp -v zImage /media/boot

Install Kernel Device Tree Binary

Info
iconfalse
title~/smarc-fimx6-sumo-release/<build dir>/tmp/deploy/images/<machine name>/
$ sudo mkdir -p /media/boot/dtbs
$ sudo cp -v zImage-imx6q-smarcfimx6.dtb /media/boot/dtbs/imx6q-smarcfimx6.dtb
$ sudo cp -v zImage-imx6dl-smarcfimx6.dtb /media/boot/dtbs/imx6dl-smarcfimx6.dtb
$ sudo cp -v zImage-imx6qp-smarcfimx6.dtb /media/boot/dtbs/imx6qp-smarcfimx6.dtb
Note
titleNote, ~/smarcfimx6-sumo-release/<build dir>/tmp/deploy/images/<machine name>
  1. If you are using LVDS panel, copy the corresponding device tree blob into SD card as follows.

For

WVGA

(800x480)

LVDS

panel:

$

sudo

cp

-v

imx6q-smarcfimx6-wvga.dtb

/media/boot/dtbs/imx6q-smarcfimx6.dtb

$

sudo

cp

-v

imx6dl-smarcfimx6-wvga.dtb

/media/boot/dtbs/imx6dl-smarcfimx6.dtb

 

$

sudo

cp

-v

imx6qp-smarcfimx6-wvga.dtb

/media/boot/dtbs/imx6qp-smarcfimx6.dtb


For

XGA

(1024x768)

LVDS

panel:

 $

$ sudo

cp

-v

imx6q-smarcfimx6-xga.dtb

/media/boot/dtbs/imx6q-smarcfimx6.dtb

 

$

sudo

cp

-v

imx6dl-smarcfimx6-xga.dtb

/media/boot/dtbs/imx6dl-smarcfimx6.dtb

$

sudo

cp

-v

imx6qp-smarcfimx6-xga.dtb

/media/boot/dtbs/imx6qp-smarcfimx6.dtb

 

For

WXGA

(1366x768)

LVDS

panel:

 $

$ sudo

cp

-v

imx6q-smarcfimx6-wxga.dtb

/media/boot/dtbs/imx6q-smarcfimx6.dtb

 

$

sudo

cp

-v

imx6dl-smarcfimx6-wxga.dtb

/media/boot/dtbs/imx6dl-smarcfimx6.dtb

$

sudo

cp

-v

imx6q-smarcfimx6-wxga.dtb

/media/boot/dtbs/imx6q-smarcfimx6.dtb

 

For

1080p

(1920x1080)

LVDS

panel:

 

$

sudo

cp

-v

imx6q-smarcfimx6-1080p.dtb

/media/boot/dtbs/imx6q-smarcfimx6.dtb

 $

sudo

cp

-v

imx6dl-smarcfimx6-1080p.dtb

/media/boot/dtbs/imx6dl-smarcfimx6.dtb

 $

sudo

cp

-v

imx6q-smarcfimx6-1080p.dtb

/media/boot/dtbs/imx6q-smarcfimx6.dtb

Install Root File System


Copy Root File System:

Yocto Built Rootfs:

Info
iconfalse
title~/smarc-fimx7-morty-release/<build dir>/tmp/deploy/images/<machine name>/

$ sudo tar jxvf <filename.tar.bz2> -C /media/rootfs
Note
titleNote
  1. SMARC-FiMX6 always boots up to SPI flash first. The firmware in SPI flash is factory pre-installed from Embedian. It will read the BOOT_SEL configuration that defined by SMARC specification on your carrier board and load u-boot.bin from the partition one of the device (could be SD card, eMMC, GBE,..etc) that you selected to memory.
  2. MAC address is factory pre-installed at on board I2C EEPROM at offset 60 bytes. It starts with Embedian's vendor code 10:0D:32. u-boot will read it and pass this parameter to kernel.
  3. The kernel modules is included in the Yocto rootfs.

Remove SD card:

Info
iconfalse
$ sync
$ sudo umount /media/boot
$ sudo umount /media/rootfs

Feed Packages 


The following procedure can be used on a Embedian SMARC-FiMX6 device to download and utilize the feed file show above to install the tcpdump Ethernet packet analyzer program:

Info
iconfalse
$ smart channel -y --add http://www.embedian.com/smarcfimx6-yocto-sumo-feed/imx6q_qt5fb_update.repo
$ smart update
$ smart install tcpdump

 

Writing Bitbake Recipes


In order to package your application and include it in the root filesystem image, you must write a BitBake recipe for it.

When starting from scratch, it is easiest to learn by example from existing recipes. 

Example HelloWorld recipe using autotools

For software that uses autotools (./configure; make; make install), writing recipes can be very simple:

 

DESCRIPTION = "Hello World Recipe using autotools"
SECTION = "console/utils"
PRIORITY = "optional"
LICENSE = "GPL"
PR = "r0"
  
S = "${WORKDIR}/git"
  
inherit autotools

 

SRC_URI specifies the location to download the source from. It can take the form of any standard URL using http://, ftp://, etc. It can also fetch from SCM systems, such as git in the example above.

PR is the package revision variable. Any time a recipe is updated that should require the package to be rebuilt, this variable should be incremented.

inherit autotools brings in support for the package to be built using autotools, and thus no other instructions on how to compile and install the software are needed unless something needs to be customized.

S is the source directory variable. This specifies where the source code will exist after it is fetched from SRC_URI and unpacked. The default value is ${WORKDIR}/${PN}-${PV}, where PN is the package name and PV is the package version. Both PN and PV are set by default using the filename of the recipe, where the filename has the format PN_PV.bb.

Example HelloWorld recipe using a single source file

This example shows a simple case of building a helloworld.c file directly using the default compiler (gcc). Since it isn’t using autotools or make, we have to tell BitBake how to build it explicitly.

 

DESCRIPTION = "HelloWorld"
SECTION = "examples"
LICENSE = "GPL"
  
SRC_URI = "file://helloworld.c"
  
S = "${WORKDIR}"
  
do_compile() {
    ${CC} ${CFLAGS} ${LDFLAGS} helloworld.c -o helloworld
}
  
do_install() {
    install -d ${D}${bindir}
    install -m 0755 helloworld ${D}${bindir}
}

 

In this case, SRC_URI specifies a file that must exist locally with the recipe. Since there is no code to download and unpack, we set S to WORKDIR since that is where helloworld.c will be copied to before it is built.

WORKDIR is located at ${OETREE}/<build directory>/tmp/work/cortexa9hf-neon-poky-linux-gnueabi/<package name and version> for most packages. If the package is machine-specific (rather than generic for the cortexa9hf architecture), it may be located in the imxq1gsmarc-poky-linux-gnueabi subdirectory depending on your hardware (this applies to kernel packages, images, etc).

do_compile defines how to compile the source. In this case, we just call gcc directly. If it isn’t defined, do_compile runs make in the source directory by default.

do_install defines how to install the application. This example runs install to create a bin directory where the application will be copied to and then copies the application there with permissions set to 755.

D is the destination directory where the application is installed to before it is packaged.

${bindir} is the directory where most binary applications are installed, typically /usr/bin.

For a more in-depth explanation of BitBake recipes, syntax, and variables, see the Recipe Chapter of the OpenEmbedded User Manual.

Setup eMMC


Setting up eMMC usually is the last step at development stage after the development work is done at your SD card or NFS environments. From software point of view, eMMC is nothing but a non-removable SD card on board. For SMARC-FiMX6, the SD card is always emulated as /dev/mmcblk1 and on-module eMMC is always emulated as /dev/mmcblk3. Setting up eMMC now is nothing but changing the device descriptor. 

This section gives a step-by-step procedure to setup eMMC flash. Users can write a shell script your own at production to simplify the steps.

First, we need to backup the final firmware from your SD card or NFS.

Prepare for eMMC binaries from SD card (or NFS):

Insert SD card into your Linux PC. For these instructions, we are assuming: DISK=/dev/mmcblk0, "lsblk" is very useful for determining the device id.

For these instruction, we are assuming: DISK=/dev/mmcblk0, "lsblk" is very useful for determining the device id.

Info
iconfalse
$ export DISK=/dev/mmcblk0

Mount Partitions:

On some systems, these partitions may be auto-mounted...

Info
iconfalse
$ sudo mkdir -p /media/boot/
$ sudo mkdir -p /media/rootfs/
 
for: DISK=/dev/mmcblk0
$ sudo mount ${DISK}p1 /media/boot/
$ sudo mount ${DISK}p2 /media/rootfs/
 
for: DISK=/dev/sdX
$ sudo mount ${DISK}1 /media/boot/
$ sudo mount ${DISK}2 /media/rootfs/

 

Copy zImage to rootfs partition:

Info
iconfalse
title~/smarc-fimx6-sumo-release/<build dir>/tmp/deploy/images/<machine name>
$ sudo cp -v zImage /media/rootfs/home/root

Copy uEnv.txt to rootfs partition:

Copy and paste the following contents to /media/rootfs/home/root ($ sudo vim /media/rootfs/home/root/uEnv.txt)

Info
iconfalse
#####HDMI######
#optargs="video=mxcfb0:dev=hdmi,1280x720M@60,if=RGB24,bpp=32 consoleblank=0"
#####LVDS#####
#optargs="video=mxcfb0:dev=ldb,if=RGB24,bpp=32 consoleblank=0 fbmem=24M vmalloc=400M"
#####Parallel LCD Setting#####
#optargs="video=mxcfb0:dev=lcd,CLAA-WVGA,if=RGB24,bpp=32 consoleblank=0 fbmem=24M vmalloc=400M"
#####Parallel LCD to CH7055A (VESA Timing Format) Setting #####
#optargs="video=mxcfb0:dev=lcd,768x576M@75,if=RGB24,bpp=32 consoleblank=0"
#optargs="video=mxcfb0:dev=lcd,1280x1024M@60,if=RGB24,bpp=32 consoleblank=0"
#optargs="video=mxcfb0:dev=lcd,640x480M@60,if=RGB24,bpp=32 consoleblank=0"
console=ttymxc4,115200
mmcdev=2
mmcpart=1
image=zImage
loadaddr=0x12000000
fdt_addr=0x18000000
mmcroot=/dev/mmcblk3p2 ro
mmcrootfstype=ext4 rootwait fixrtc
netdev=eth0
ethact=FEC0
ipaddr=192.168.1.150
serverip=192.168.1.53
gatewayip=192.168.1.254
mmcargs=setenv bootargs console=${console} root=${mmcroot} rootfstype=${mmcrootfstype} ${optargs}
uenvcmd=run loadzimage; run loadfdt; run mmcboot

Copy device tree blob to rootfs partition:

Info
iconfalse
title~/smarc-fimx6-sumo-release/<build dir>/tmp/deploy/images/<machine name>
$ sudo cp -v imx6q-smarcfimx6.dtb /media/rootfs/home/root/imx6q-smarcfimx6.dtb
$ sudo cp -v imx6dl-smarcfimx6.dtb /media/rootfs/home/root/imx6dl-smarcfimx6.dtb 
$ sudo cp -v imx6qp-smarcfimx6.dtb /media/rootfs/home/root/imx6qp-smarcfimx6.dtb 
Note
title~/smarcfimx6-sumo-release/<build dir>/tmp/deploy/images/<machine name>
  1. If you are using LVDS panel, copy the corresponding device tree blob into SD card as follows.
For WVGA (800x480) LVDS panel:

$ sudo cp -v imx6q-smarcfimx6-wvga.dtb /media/rootfs/home/root/imx6q-smarcfimx6.dtb 

$ sudo cp -v imx6dl-smarcfimx6-wvga.dtb /media/rootfs/home/root/imx6dl-smarcfimx6.dtb 

$ sudo cp -v imx6qp-smarcfimx6-wvga.dtb /media/rootfs/home/root/imx6qp-smarcfimx6.dtb

 
For XGA (1024x768) LVDS panel:

$ sudo cp -v imx6q-smarcfimx6-xga.dtb /media/rootfs/home/root/imx6q-smarcfimx6.dtb 

$ sudo cp -v imx6dl-smarcfimx6-xga.dtb /media/rootfs/home/root/imx6dl-smarcfimx6.dtb 

$ sudo cp -v imx6qp-smarcfimx6-xga.dtb /media/rootfs/home/root/imx6qp-smarcfimx6.dtb

 
For WXGA (1366x768) LVDS panel:

$ sudo cp -v imx6q-smarcfimx6-wxga.dtb /media/rootfs/home/root/imx6q-smarcfimx6.dtb 

$ sudo cp -v imx6dl-smarcfimx6-wxga.dtb /media/rootfs/home/root/imx6dl-smarcfimx6.dtb 

$ sudo cp -v imx6qp-smarcfimx6-wxga.dtb /media/rootfs/home/root/imx6qp-smarcfimx6.dtb

 
For 1080p (1920x1080) LVDS panel:

$ sudo cp -v imx6q-smarcfimx6-1080p.dtb /media/rootfs/home/root/imx6q-smarcfimx6.dtb 

$ sudo cp -v imx6dl-smarcfimx6-1080p.dtb /media/rootfs/home/root/imx6dl-smarcfimx6.dtb 

$ sudo cp -v imx6qp-smarcfimx6-1080p.dtb /media/rootfs/home/root/imx6qp-smarcfimx6.dtb


Copy real rootfs to rootfs partition:

Info
iconfalse
$ pushd /media/rootfs
$ sudo tar cvfz ~/smarcfimx6-emmc-rootfs.tar.gz .
$ sudo mv ~/smarcfimx6-emmc-rootfs.tar.gz /media/rootfs/home/root
$ popd

Remove SD card:

Info
iconfalse
$ sync
$ sudo umount /media/boot
$ sudo umount /media/rootfs

Copy Binaries to eMMC from SD card:

Insert this SD card into your SMARC-FiMX6 device.

Now it will be almost the same as you did when setup your SD card, but the eMMC device descriptor is /dev/mmcblk2 now.

Info
iconfalse
$ export DISK=/dev/mmcblk3

Erase SD card:

Info
iconfalse

$ sudo dd if=/dev/zero of=${DISK} bs=1M count=16

Create Partition Layout:

Info
iconfalse

$ sudo sfdisk ${DISK} <<-__EOF__
1M,48M,0x83,*
,,,-
__EOF__

Format Partitions:

Info
iconfalse
$ sudo mkfs.vfat -F 16 ${DISK}p1 -n boot
$ sudo mkfs.ext4 ${DISK}p2 -L rootfs

Mount Partitions:

Info
iconfalse
$ sudo mkdir -p /media/boot/
$ sudo mkdir -p /media/rootfs/
$ sudo mount ${DISK}p1 /media/boot/
$ sudo mount ${DISK}p2 /media/rootfs/

Install binaries for partition 1

Copy uEnv.txt/zImage/*.dtb to the boot partition

Info
iconfalse

$ sudo cp -v zImage uEnv.txt /media/boot/

Install Kernel Device Tree Binary

Info
iconfalse
$ sudo mkdir -p /media/boot/dtbs
$ sudo cp -v imx6q-smarcfimx6.dtb imx6dl-smarcfimx6.dtb /media/boot/dtbs

Install Root File System


Info
iconfalse
$ sudo tar -zxvf smarcfimx6-emmc-rootfs.tar.gz -C /media/rootfs

 

Unmount eMMC:

Info
iconfalse
$ sync
$ sudo umount /media/boot
$ sudo umount /media/rootfs

 

Switch your Boot Select to eMMC and you will be able to boot up from eMMC now.


version 1.0a, 1/29/2019

Last updated 2019-11-16